TOP 10 TYPICAL FORKLIFT MISHAPS , FORKLIFT OPERATION OUGHT TO TAKE NOTE OF THESE MATTERS !.

Top 10 typical forklift mishaps , forklift operation ought to take note of these matters !.

Top 10 typical forklift mishaps , forklift operation ought to take note of these matters !.

Blog Article


Do not ignore the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps entailing forklifts.

Case 1: The forklift freight blocked the motorist's view, and the individual ahead might not be located, causing a moving mishap.
Situation 2: In order to preserve the balance of the forklift when lifting heavy products, the workers used their body weight as the counterweight, which almost caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees illegally, the forklift chauffeur does not wear the safety belt, the forklift lifter falls and the driver is squashed when the forklift surrender.
Case 7: The forklift vehicle driver did not put on a seat belt and dropped from the automobile when it rolled over and was squashed.
Forklift operation should pay attention to these issues :.

Start.
1. Prior to starting, observe the surroundings, and after confirming that there are no obstacles that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a load, the vehicle driver ought to initially confirm that the lots is stable and reliable.
4. The begin has to be sluggish and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is taking a trip, the fork must not be increased expensive, which will certainly affect the security of the forklift. .
3. After dumping, the fork ought to be reduced to the regular driving position before driving. .
4. When turning, if there are pedestrians or lorries close by, the driving signal should be provided initially. High-speed doglegs are prohibited. High-speed sharp turns will trigger the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake instantly while driving with loads unless there are special scenarios.
6. When the forklift is running, it needs to comply with the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry should be correctly tilted back. The load shall not be raised other than when stacking or loading. .
8. The height of the load must not block the driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it must drive securely at a reduced speed when entering the production workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to depend on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with diseases or hide them.

packing and unloading.
1. When fork-loading items, the range between both forks must be adjusted as required to make the tons of both forks well balanced and not skewed, and one side of the thing should protest the rack. .
2. It is restricted to deal with a single fork or make use of a fork top or pull. In unique situations, safety indication must be established to remind bordering pedestrians. .
3. In the process of loading and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork suggestion need to not touch other products or things. The load must be stabilized with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted ahead a little when the load is reduced to permit very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is forbidden for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or depress the parking brake button.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, check whether the pressure and temperature are normal.
5. After the forklift is running, the external leak needs to Stand-on Electric Pallet Stacker likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check prior to leaving the auto;.
2. When you come across somebody before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming ought to not be too sharp to stop the tendency of " cost-free turning";.
6. Adding and down the slope should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy products and go to the motorist's view, they ought to take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork procedure is not allowed.
2. It is not permitted to lift the goods for far Electric Forklift Truck for Warehouse away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.

Web:https://www.onenforklifts.com/
Email:info2@onen.cn
Phone:+86 13827083844

Report this page